*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*
+ Frequently Asked Questions with answers for RAMTRUCK mailing list +
*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*+*
This is the FAQ list for the Mailing list ramtruck,
maintained by Hank Janssen (hjanssen@anteus.com),
with contributions from many other people (see the credits
section). The contents of this document are based on the
contributors' opinions; neither the contributors nor the FAQ
maintainer accept any responsibility or liability for any
damages brought about by the information contained herein.
This document may be freely distributed and reproduced as long
as it remains wholly unaltered and includes this notice. If
you do redistribute this document, especially on a commercial
basis, please contact the FAQ maintainer before doing so.
If you have suggestions for improvements to this document, or
if you fail to understand any part of it, please feel free to
send a note to the FAQ maintainer or to the author of the
relevant section. The initials of the author(s) of each
section can be found in brackets following each question.
This document is intended for those people interested in or driving
a Dodge RAM truck. Such as (but not limited to) the 1500, 2500 and
3500 series.
I myself decided to start this FAQ, I own a 97 Dodge 2500 Club Cab
with an Cummins diesel engine. I am a new first time dodge owner,
and I love this truck. The truck is used, besides day to day work
driving, for Search And Rescue in the Washington area, mainly in the
Cascade and Olympic mountains.
Changes to the FAQ
======= == === ===
Additions since the last posting (03/19/98)
------------------------------------------
Added more info the the max size tires fitting a 1500.
Additions since the last posting (02/02/98)
------------------------------------------
Added more info to acronyms chapter.
Additions since the last posting (11/13/97)
------------------------------------------
Added more info to customizations chapter, and to the diesel chapter.
Additions since the last posting (7/7/97)
-----------------------------------------
Added info from John Donovan that pretty much filled in chapter 7.!
Updates for release on (7/2/97)
-------------------------------
With the help of many, I filled in a lot of the TBD area's. And
added a whole bunch of extras.
Updates for release on 6/10/97
------------------------------
Changed some email address and added a new web site for info.
Updates for release on 4/25/97
------------------------------
Extended the FAQ significantly and spell checked the whole thing.
Updates for release on (4/24/97)
--------------------------------
First sending for hints/approvals etc.
Table of Contents
===== == ========
0 Introduction and Table of Contents.
0.1 Who am I.
1 Definitions
1.1 What do all of those acronyms mean (4x2, 4x4)?
2 Finding out about the Dodge Ram truck.
2.1 Phone numbers.
2.2 What is a 1500.
2.2.1 General
2.2.2 What are the engines available.
2.2.3 What are the dimensions/Performance
Data.
2.3 What is a 2500.
2.3.1 General
2.3.2 What are the engines available.
2.3.3 What are the dimensions/Performance Data.
2.4 What is a 3500.
2.4.1 General
2.4.2 What are the engines available.
2.4.3 What are the dimensions/Performance Data.
2.5 What mileage have people been getting.
3 Maintenance
3.1 What kinds of oil are people using.
3.2 What kinds of oil filters are people using.
4 Performance upgrades and guidelines
4.1 What can I do to make my truck go faster.
4.1.1 Biggest performance bang for the $$
4.2 What are kind of tires will/are the best for my truck.
4.2.1 Tire Pressures.
4.2.2 What are the biggest tires that fit on a 1500.
4.2.3 What are the biggest tires that fit on a 2500.
4.2.4 What are the biggest tires that fit on a 3500.
4.3 What is an Borla Exhaust. (+ installation)
4.4 Shocks.
4.5 Gear Ratios.
4.6 Axle Info.
4.7 US Gear Overdrive/Underdrive.
4.8 K&N Airfilters and FIPK.
5 Customizations.
5.1 Bed-liners.
5.2 Running boards.
5.3 Brush Guards.
5.4 Side Bars.
5.5 Aero Tanks.
5.6 Lights.
5.7 Better brake pads.
6 The Cummins diesel engine
6.1 Oil pressure delay.
6.2 What kinds of oil are people using for the Cummins Diesel.
6.3 Biggest performance bang for the $$ for diesels.
6.4 What is this ISB engine I keep hearing about.
7 What about more 4x4 info.
7.1 What's that lever for?
7.2 Where are my hubs?
7.3 Stock, shmock, I want to lift it!
7.3.1 Available lift kits
7.4 If its four wheel drive, why am I stuck?
7.4.1 Brief description of traction aiding devices
7.4.2 List of factory available LSD's
7.4.3 List of aftermarket LSD's/lockers
7.4.4 Why you can't use an LSD in a front CAD system
7.5 Help, I'm stuck!
7.5.1 Description of factory tow hooks, installation
7.5.2 Aftermarket winch bumpers
7.6 How to tow a 4x4
8 Various helpful sites.
9 Credits.
==========================================================================
1 Definitions
This is a list of common abbreviations used in this FAQ.
2WD 2 Wheel Drive.
4WD 4 Wheel Drive.
CC Chrysler Corporation.
FIPK Fuel Injection Performance Kit.
OBD II 2nd generation On Board Diagnostics (Federally required
computer system to check engine problems that could lead to any
increase in emissions)
ISB Interact System B (refers to Cummins B-series diesel with new
Interact System computer controls)
TST company that makes Cummins uprate kits http://www.tstproducts.com/
TSB Technical Service Bulletin (repair issued by manufacturer in
response to common problems amongst a similar group of
vehicles) You can find a list of them at http://www.alldata.com/
(the following numbers are only valid in the US)
1-800-992-1997 Chrysler Customer Service
1-800-255-9877 Auto-mobility Headquarters (info about reimbursements
for aftermarket adaptation of new vehicles for people
with disabilities)
1-800-253-0823 order a catalog of replicas of Chrysler vehicles
1-800-4-A-DODGE get a Dodge catalog or other product info
1-812-342-6741 TST line. HP upgrade kit company for the Cummins.
(the following number is valid if you're not in the US)
810-978-6428 Chrysler International
This section describes the various 1500 models available. These are
based on the 1997 model year.
The 1500 Series truck come in several (base) options.
Dodge Ram 1500 WS 2WD Regular Cab Short bed.
Dodge Ram 1500 WS 2WD Regular Cab Long bed.
Dodge Ram 1500 LT 2WD Regular Cab Short bed.
Dodge Ram 1500 LT 2WD Regular Cab Long bed.
Dodge Ram 1500 LT 4WD Regular Cab Short bed.
Dodge Ram 1500 LT 4WD Regular Cab Long bed.
Dodge Ram 1500 ST 2WD Club Cab Short bed.
Dodge Ram 1500 ST 2WD Club Cab Long bed.
Dodge Ram 1500 ST 4WD Club Cab Short bed.
Dodge Ram 1500 ST 4WD Club Cab Long bed.
V6 Only. (3.9L) (V6 is only option)
Dodge Ram 1500 WS 2WD Regular Cab Short bed.
Dodge Ram 1500 WS 2WD Regular Cab Long bed.
V6/V8/V8. (3.9L/5.2L/5.9L)
Dodge Ram 1500 LT 2WD Regular Cab Short bed
Dodge Ram 1500 LT 2WD Regular Cab Long bed.
Dodge Ram 1500 LT 4WD Regular Cab Short bed.
Dodge Ram 1500 LT 4WD Regular Cab Long bed.
V8/V8. (5.2L/5.9L)
Dodge Ram 1500 ST 2WD Club Cab Short bed.
Dodge Ram 1500 ST 2WD Club Cab Long bed.
Dodge Ram 1500 ST 4WD Club Cab Short bed.
Dodge Ram 1500 ST 4WD Club Cab Long bed.
For an up to date list of dimensions/performance data for
stock 1500 please check out;
http://www.edmunds.com/edweb/trucks/Dodge.Trucks.html
The list is so long, it would take up way to much space.!
This section describes the various 2500 models available. These are
based on the 1997 model year.
Dodge Ram 2500 2WD Heavy Duty Regular Cab.
Dodge Ram 2500 4WD Heavy Duty Regular Cab.
Dodge Ram 2500 2WD Club Cab Short bed.
Dodge Ram 2500 2WD Club Cab Long bed.
Dodge Ram 2500 4WD Club Cab Shortbed.
Dodge Ram 2500 4WD Club Cab Longbed.
V8/V10. (5.9L/8.0L)
Dodge Ram 2500 2WD Club Cab Shortbed.
Dodge Ram 2500 4WD Club Cab Shortbed.
V8/V10/Cummins Diesel. (5.9L/8.0L/5.9L)
Dodge Ram 2500 2WD Heavy Duty Regular Cab.
Dodge Ram 2500 4WD Heavy Duty Regular Cab.
Dodge Ram 2500 2WD Club Cab Longbed.
Dodge Ram 2500 4WD Club Cab Longbed.
For an up to date list of dimensions/performance data for
stock 2500 please check out;
http://www.edmunds.com/edweb/trucks/Dodge.Trucks.html
The list is so long, it would take up way to much space.!
This section describes the various 3500 models available. These are
based on the 1997 model year.
This is pretty much the biggest one you can get, dual wheels in the
back, and really designed for heavy duty towing.
Dodge Ram 3500 2WD Regular Cab Duallie.
Dodge Ram 3500 4WD Regular Cab Duallie.
Dodge Ram 3500 2WD Club Cab Duallie.
Dodge Ram 3500 4WD Club Cab Duallie.
V8/V10/Cummins Diesel. (5.9L/8.0L/5.9L)
Dodge Ram 3500 2WD Regular Cab Duallie.
Dodge Ram 3500 4WD Regular Cab Duallie.
Dodge Ram 3500 2WD Club Cab Duallie.
Dodge Ram 3500 4WD Club Cab Duallie.
For an up to date list of dimensions/performance data for
stock 3500 please check out;
http://www.edmunds.com/edweb/trucks/Dodge.Trucks.html
The list is so long, it would take up way to much space.!
What mileage people have been getting with their RAM's is of course
very subjective due to setup and driving conditions. But here are
some mileage numbers.
Me, 2500 4x4 97 Cummins Diesel. about 21 miles to the gallon, 35%
city 65% highway at speeds of 75 miles. Only have a K&N drop in air
filter.
Chris 2500 V10. 10.5 city 12 Highway.
CC 4X4, Auto, stock tires. I have a K&N element.
Franco C. Saiano <> 97 2500HD SLT 4X4 V-10/5 speed, I'm getting
about 9-10 MPG in 2WD with no payload.
I get about 11.5 average with 65% city driving and 35% highway. I
have a '96 v10 CC 4x4 with a K&N drop in filter, dynomax dual
exhaust cat back and a FloThru tailgate. I believe that my setup
gives me about 1.5 to 2.0 MPG more than if I left the truck
entirely stock. I use 87 octane, after much trial and error. I
found the 87 gives me the best performance and mileage.
Michael P. Lebow
I don't get it, I am a big lead foot, and I get 11.5 city min and 15
highway. This is corrected speed, and on a 4x4 2500 extended cab. Its
white, maybe that helps.
Oh, 5sp, cruise at max (87MPH) and BFG 245/75r16. Inflation
pressure makes a difference. 80 is best but doesn't wear well. So
50-60psi is what i run. only change was new tranny fluid and
synthetic gear oil for diffs. Oh and a K&N.
wrote on this;
I use Mobil 1 10w-30. I may try the 0w-30 at my next oil change.
wrote on this;
I use the designated Fram Filter for the 360. I know some others are
using the Fleetguard Microglass but you must buy those by the case.
J. Lacey <7th_nhrc@interoz.com> wrote on this;
Called around today, 3 different states, 7 different Cummins
dealers - no LF3604 oil filters. They never heard of it! Or the
3313 or the 3487; all fit the V10 & 318 & 360. Whoever was told by
Fleetguard that Cummins would have them available 'everywhere' has
their head up their butt. Every single dealer said they would not
even stock them, period. Simply no call.
Some History: Fleetguard company makes oil filters, both the usual
paper AND a newer type, that soon everyone will be providing, and
they call it a Microglass filter. This is probably the best money
can buy. Fleetguard's part #'s for their filters for CC V8s:
LF3604, 3/4" opening, 16 thread, paper, 3.7" length
LF3313, 3/4" opening, 16 thread; paper, 5.4" length
* LF3487, 3/4" opening, 16 thread; Microglass, length? (one of above)*
(the one you want; cost < than $10)
This section provides you with some insight as to what some people
on the ramtruck mailing list have done to their truck to improve
the performance and guidelines to keep in mind when you want to
improve the performance.
Can you ever go to fast.?? Here are some things people on the list
have done to get that extra mile.
Here is a list that went around on the list some time ago, it shows
what people suggest to do to increase the performance of their
(gas) engines.
Mike (mikes@phoenix.net) suggests;
Optimal order for purchase:
1: Cat-back
2: Headers
3: mopar chip
4: Throttle body from magnum performance
Christopher Siano (Chris_Siano@AutoSite.com) Suggests;
The performance computer is the biggest bang for buck improvement
you can make. Just remember the minuses. 93 Octane fuel, hates
to tow, and don't carry too much of a load. Keep the old computer
for those times you need to use cheap fuel, tow something, or haul
a major load.
Steve Belt (Stephen_D_Belt@ccm.ch.intel.com) Suggests;
1st: Borla Cat-back
2nd: TBI Pro-Street w/ Mystery Shaft
3rd: Borla Headers
I haven't considered the SBEC, because I'm not too comfortable
with the down sides. Maybe after all of the other things are done,
I'll look into it. With the gear change done, it is now a possibility.
What I will do, however, is give you feedback after each item is put
on the truck, as this may help you decide.
And then previous to the above I did:
1st: K&N
2nd: New plugs
3rd: Magnecor plug wires
4th: TransGo Shift Kit
BTW, the TransGo is my favorite "bang-for-the-buck" item so far....
This (as most things in this FAQ) is a tricky question to
answer. Many people reported bad experiences with the stock
Goodyear tires. Keep in mind also, the bigger/smaller the tire than
a stock tire will throw your speedometer off, sometimes enough that
you need a speedo gear adjustment to make your speedo sane again. :)
Here are a few people and the tires they recommend/have on their
own truck(s);
Steve Belt (Stephen_D_Belt@ccm.ch.intel.com)
(About the stock tires.) To me, these tires seem ill-suited for
application on a 3/4 ton truck. By the way, they were 245/75R16s.
I have since switched to BFG Mud/AT tires. As far as I know, these
tires have extremely strong side wall strength. I have accidentally
nailed many a curb or hard rock. There is no sidewall bruising
evident after 9k miles. The tread, while showing a bit of wear,
also looks great. The tires perform well on and off road. They are
a bit noisy, due to the tread pattern, and I probably wouldn't want
them on a 4x2 truck. BFG makes an All-Terrain tire that I recommend
to every Ram Truck owner that wants to "upgrade" from the stock
Goodyear rubber.
Dennis A. Grindrod Sr (grinny@snet.net)
Well thanks to all your input I went out and bought 4 new Dunlop 265x15
radial rover tires and I must say they rode like a dream on a 500 mile
trip to Pa. The difference between the stock Goodyear 245x16 and the
Dunlop 265x16 is night & day. I put these on my RAM 2500 360ci. 5
speed 2WD.
Several people seem to have changed their tire pressure on their
trucks to counter for heavy loads and or tire wear. Here are some
of the pressures people seem to be using (Please note that tire
pressure is also directly related to the type(s)/truck of tire you
have on your truck!!);
Tim Edwards (T_Edwards@eagle2.stark.k12.oh.us) Writes;
I have a 2500 HD Cummins with the factory 245 70R16's on it. They
are of course Good Year tires. I run 55 to 60 pounds in the front
and 45 in the rear when lite. Just add air to give a full foot
print on the road when you load the rear of the truck. One note,
at 9000 miles one of the tires grew a flat spot and caused all
kinds of problems until it was diagnosed. When on the front end it
made the truck drive like it needed a front end alignment. Good
Year is replacing the tire for $60 based on tread wear.....
Joe (Drdonnelly@aol.com) Writes;
I have an 2500. With the diesel, I usually run about 54 front, 46
rear. My D rated 255-85-16s can go up to 60 lb for 3000 lb load.
Bob Ballard (rballard@visuallink.com) Writes;
(96 1500, 4x4) I have 25,000 on my wranglers RTS and they still
look like new. No feathering, cupping. I do not like the tires at
all because of their behavior in the mud, snow and so forth. I
usually ran with 38psi up front and 35psi rear and rotated every
6,000 miles.
Several people on the list indicated that the biggest tires that
fit a _stock_ 1500 2WD (probably same for 4WD) are 265/75R16.
Bryan Wilemski send me email with the following;
In your FAQ about tires you have a statement about the biggest tire to fit
a RAM. I put 285 70R 16 on my 1997 RAM 1500 4x4. It did rub sometimes on
MAX wheel turns but I adjusted the MAX turn in a little and it does not rub
anymore. I can't fit it in my garage but it stands tall on the trails.
rolando Gonzalez (Lando-G@msn.com) wrote on this;
I have 33/12.5/16.5 BF Goodrich Radial TA's on my '97 2500HD
4x4. They have rubbed only once on the front. Must of been when I
hit that one bump. You won't be able to turn the front tires if you
put 35's.
TBD
A Borla Exhaust is a Dual Exhaust. Used to provide a more "powerful"
sound and increase performance.
Darin L Brummett (darinb@juno.com) Writes;
I have a Borla Cat-back exhaust and the K&N FIPK installed on my
1500 4x4 5.9L. The Borla Cat-back system mates to the output of
the stock cat (single pipe 2.75 inch, I think) and runs thru a muffler
where it is split in to two pipes (2.25 inch, again I think) and exits
behind the right rear tire. They also make a version that exits
out the rear. The Borla has Cat-back system adds a wonderful V8
rumble compared to the stock exhaust but isn't too loud IMHO. My
experience has been added horsepower, increased MPG and increased
drivability (especially on mountain roads and highways). It has
also lessened the auto transmission downshifting problem going up
hills.
J Lacey <7th_nhrc@interoz.com> wrote on this;
Borla Stainless-Steel Cat-Back, part# 14591, for 1996 V8
Ordered from Summit Racing but they could only back-order, so
system was drop-shipped from Borla in Calif. Their Cat-back exhaust
is interesting, rather straight-forward to install, can be done by
single person 1/2 day, comes with zero instructions. Mine is
2-pipes exit behind the R R tire and the hanger there is welded &
pointed 90* off so you got to go to local installer with torch for
fix when finished. 30 days after installation I crawled under and
where it clamps before the muffler found 2 leaks; could feel them
with fingers when truck running. Their clamps ain't going get it!
And for no explainable reason the pipes they include are notched
(3/4 in.). Back to local exhaust installer with Ming welder who
immediately burns hole in THEIR pipe right where that useless 3/4
in. notch is (cause it is SUPER DAMN THIN! ). Can't be fixed -
gotta cut it out & replace - no one in this town has stainless
pipe we could purchase.
So had to use the old tried & true usual exhaust pipe, fitting in a
piece about 20" long, BUT I'm sure there goes the *Life-Time
Warranty*. No more leaks! I believe Borla actually intends us to
clamp these systems together but they are going to leak, don't
think we can get around that.
Borla Stainless-Steel Header, part# 17077 Ordered from Summit
Racing mid-August but they could only back-order, so system was
drop-shipped from Borla in Calif.
First, in September, they sent the old style, fits only the
'94-'95, and acted so surprised when I called to say I did not have
the emissions connection on the header they thought. It was then I
alerted this list by posting the part# of 17077 for the 1996 V8 and
caught lots of flak from others on same list using the same
catalog #'s as all other agents selling Borla. Send them back; they
said they would have to make special for me, 2 weeks. Sure enough,
then came another large box - in October - contained 1995 Jeep
header. Sent them back; they said they would have to make special for
me, another 2 weeks. Finally arrived in November with zero
instructions, which the company contends is not uncommon, and they
faxed me a drawing, saying these were for export and off-the-road
use only.
You need to know this is not bolt-on system - it requires welding,
is designed that way from Borla, yet they did not tell us that when
the purchase order was phoned in back in August. Passenger side
installs easy. Driver side MUST go on from beneath after removing
the starter and forcing tranny return lines to the side. Not a
tough job. Small connection pipes they provide are pretty much
right on but they ask you to have your local installer weld an end
on your cat-converter so there is going to be an added cost.
Actually what we did, BECAUSE of experiencing leaks with clamping
on the cat-back exhaust system was weld the whole damn
system. Cures all leaks and I can foresee no reason I would be
pulling the system apart as long as I own RAM. Just tough heading
out thru local traffic on a Saturday for the shop sounding like
Richard Petty! Noticeable performance change?
Cat-back: can not say 'yes, felt performance enhanced' but sounded
nice & did improve mpg slightly. Headers: (remember also have
cat-back) Can installing these 2 items make one feel a 5000 lb
vehicle move quicker; would I not simply be kidding myself, wanting
to believe the $$ spend improve everything? Could be. But I could
pass a lie detector test if asked, cause I believe I can actually
tell, can feel, this RAM has gained in performance. It feels,
sounds, MARVELOUS!!!
Would I do either OR both systems again? I think so. But after
some months of having both I am having MUCH trouble keeping the
header bolts tight. Have had to drill the bolts & safety wire
them. ALSO, the exhaust header gaskets that come with the Borla
system are crap - I have blown out 3; that means have had to change
THREE of them - and Borla will tell you so! Get the FelPro #1413 as
they are MUCH better and are holding so far.
The general perception of those driving a RAM seems to be that the
shocks that come from the factory are not the best ones by any
stretch of the imagination. Here are a few peoples suggestions on
changing them with something that provides a better ride.
Many people seem to lean towards the Rancho 9000 ajustable
shocks. But Edelbrock has been come out with a promising new
concept in shocks. Here are some comments from a user on the list.
Scott Bessel (sbessel@jps.net), wrote on this;
Since Friday I have been running a new set of Edelbrock IOS shocks,
one word WOW!
I have owned and used many different shocks including Koni, KYB,
Bilstein, Rancho 5000, Rancho 9000, Monroe and stock gas shocks.
NONE of these can touch what the IOS shocks can do. These shocks
live up to their claims, they give the best of both worlds, they
absorb the rough bumps, potholes and speed bumps without a whimper
or jarring your teeth out. You can then lay into a turn and they
are rock solid without ANY body roll. They shocks are far and away
better that ANY shock I have EVER used. I am sure they would even
perform better off road.
My "new" Indy can now take those 360 on-ramps at 70+ MPH without
hesitation and without scaring the life out of you, and if you hit
a rut or bump the shocks absorb it without launching the tire and
loosing traction.
What are the gear ratios available on the Ram.?
See, also 4.6 Axle Info.
Chris (Chris_Siano@AutoSite.com) Provided the following info on axles;
Dana 44-F
=========
Application: 1500 and 2500 4x4 Regular Cab, 1500 4x4 Club Cab (with
NV231HD an NV241 transfer case)
Capacity: 3,850 lbs
Type: Hypoid
Ratios avail 3.54,3.92,4.09
Ring gear Diameter 8.50
Pinion mount Overhung
Pinion shaft diameter 1.376" inner bearing
1.35" outer bearing
Differential Pinions Two
Axle Shaft material Low carbon Alloy
Axle shaft diameter 1.31" inner
1.34" outer
axle spline pitch 1.25"
Spring Centers 42.15"
Universal Single Cardian
Turning Angle 36 Degrees
Fluid capacity 4.8 pints
wheel bearing Tapered Roller
Tie Rod type Ball and socket
Tie rod diameter 1.25"
Tie rod thickness 0.156"
Ball centers 61.16"
housing pressed tubes
wall thickness .39"
Dana 60-F
=========
Application: 2500 and 3500 4x4 regular cab, 2500HD and 3500 4x4
Club Cab (with NV241 and NV241HD transfer case)
Capacity: 4,850 lbs
Type: Hypoid
Ratios avail 3.54,4.10
Ring gear Diameter 9.75"
Pinion mount Overhung
Pinion shaft diameter 1.63" inner bearing
1.25" outer bearing
Differential Pinions Two
Axle Shaft material Low carbon Alloy
Axle shaft diameter 1.31" inner
1.34" outer
axle spline pitch 1.5"
Spring Centers 42.15"
Universal Single Cardian
Turning Angle 36 Degrees
Fluid capacity 7.6 pints
wheel bearing Tapered Roller
Tie Rod type Ball and socket
Tie rod diameter 1.25"
Tie rod thickness 0.22"
Ball centers 60.15"
housing pressed tubes
wall thickness .50"
Chrysler 9.25
=============
Application: 1500, 1500 4x4 All Engines
Capacity: 3,900 lbs
type semi-floating
Ratios 3.21, 3.55, 3.92
Ring gear diameter 9.25"
Ring gear face width 1.375"
pinion mounting overhung
pinion shaft diameter 1.88" inner
1.31" outer
Differential pinions two
axle shaft material Induction Hardened
diameter at bearing 1.62"
axle spline pitch 1.29"
Spring Centers 44.50"
Fluid capacity (2/4WD) 4.75/4.75 pints
wheel bearings Cylindrical Roller
Chrysler 9.25
=============
Application: 2500HD, 2500HD 4x4, 2500, 2500 4x4 w/V8 Engines and auto
transmission (if Sure-Grip is ordered, Dana 60 is used, except for Ram
2500 4x4 models with 3.55 gear ratio.)
Capacity: 5,500 lbs
type semi-floating
Ratios 3.55, 3.92
Ring gear diameter 9.25"
Ring gear face width 1.375"
pinion mounting overhung
pinion shaft diameter 1.88" inner
1.31" outer
Differential pinions two
axle shaft material Induction Hardened
diameter at bearing 1.70"
axle spline pitch 1.29"
Spring Centers 44.50"
Fluid capacity (2/4WD) 4.75/4.75 pints
wheel bearings Cylindrical Roller
Dana 60
=======
Application: 2500 HD, 2500 HD 4x4, 2500, 2500 4x4 Manual
Transmission w/V8 engines.
Capacity: 6,200 lbs
type Full-floating
Ratios 3.54, 4.09
Ring gear diameter 9.75"
Ring gear face width N/A
pinion mounting overhung
pinion shaft diameter 1.63" inner
1.25" outer
Differential pinions two
axle shaft material Induction Hardened
diameter at bearing none
axle spline pitch 1.31"
Spring Centers 44.50"
Fluid capacity (2/4WD) 6.3/7.3 pints
wheel bearings Tapered Roller
Dana 70
=======
Application: 2500 HD, 2500 HD 4x4, 8.0L V10 and Diesel w/Auto
Transmission.
Capacity: 6,500 lbs
type Full-floating
Ratios 3.54, 4.10
Ring gear diameter 10.5"
Ring gear face width N/A
pinion mounting overhung
pinion shaft diameter 1.75" inner
1.25" outer
Differential pinions two
axle shaft material Induction Hardened
diameter at bearing none
axle spline pitch 1.375"
Spring Centers 43.26"
Fluid capacity (2/4WD) 7.0/7.8 pints
wheel bearings Tapered Roller
Dana 80
=======
Application: 2500 HD, 2500 HD 4x4, 8.0L V10 and diesel w/Manual
Transmission.
Capacity: 7,500 lbs
type Full-floating
Ratios 3.54, 4.10
Ring gear diameter 11.0"
Ring gear face width N/A
pinion mounting overhung
pinion shaft diameter 1.75" inner
1.25" outer
Differential pinions two
axle shaft material Induction Hardened
diameter at bearing none
axle spline pitch 1.375"
Spring Centers 43.26"
Fluid capacity (2/4WD) 6.8/10.1 pints
wheel bearings Tapered Roller
Dana 80 Dual Rear Wheel
=======================
Application: 3500, 3500 4x4 All Engines.
Capacity: 7,500 lbs
type Full-floating
Ratios 3.54, 4.10
Ring gear diameter 11.0"
Ring gear face width N/A
pinion mounting overhung
pinion shaft diameter 1.75" inner
1.25" outer
Differential pinions two
axle shaft material Induction Hardened
diameter at bearing none
axle spline pitch 1.375"
Spring Centers 43.26"
Fluid capacity (2/4WD) 6.8/10.1 pints
wheel bearings Tapered Roller
There seems to be a product out that can improve the mileage by
providing you with an extra 'gear'.
Stan Steele (PowerMaster@dodgeram.com), wrote on this;
This is a transmission. that bolts to your transmission. to give
you more Overdrive or a extra gear. It works on all trucks great
with V10s or diesels. if you have a 4.10 it would change to 3.28 in
Overdrive and a 3.55 would go to 2.84, you reduce your RPM by 500
or 20%. you gain 10-15MPH at the same RPM.
You up shift at any speed or down shift at any speed. You shift it
with a switch on the shifter or a floor mounted dimmer
switch. You can start in HI or direct drive it does not
matter. You have to shorten the rear drive shaft and lengthen the
front drive shaft. It does move the transfer case back but all
the hardware comes in the kit. Very well done and very easy for
anyone to install. P.S. you can split shift it also like a 10speed
1&1H 2&2H and so on.
The Overdrive is less than 100lbs on the truck. You will need to
have the drive shafts made at a shop.
An easy and pretty cheap way to increase a little performance is to
replace your stock air filter with an higher air flow filter. Many
on the list (myself included) have either a drop in replacement
filter or what is called an FIPK (both made by K&N)
These filters work on the principle of providing the engine with
more air and thus increasing it's mileage and horsepower. Although
these improvements have not been seen by all (I noticed maybe a
mile to the gallon more, and a slightly faster throttle response)
They do offer one additional benefit, they are guaranteed for the
life of your vehicle (or 1 million miles). So once you buy one, you
never have to by another. You have to clean them every so many
miles, (mine stated every 40.000 or so miles) and they are again as
good as new.
Several people on the list noted though that this filter might not
be helpful in very dusty environments. The thought was that due to
the higher airflow rates more dust might get by and foul the air
intake.
Some people noticed a slight increase in sound with this filter
installed. (A very faint high pitch whine from the air filter intake)
I have not heard this myself, but my ram is a turbo diesel that
whines by itself. :)
An K&N Airfilter is just that, a drop in replacement filter for
your stock airbox.
(From the http://www.performanceintl.com home page)
Each FIPK has a specially designed filter with special woven cotton
fabric sandwiched between 2 layers of wire mesh screen. The screen and
fabric combination creates a grid-like effect which actually
straightens out the incoming air as it passes through the
filter. In addition to the filter, this kit has a uniquely designed
adapter with a built-in velocity stack. This velocity stack is
beneficial in further smoothing out the incoming air flow and
allowing for a less restrictive entry into the engine. Air moving
in a straight direction moves faster than tumbling air thus
creating an increase in air flow much like a ram air
effect
I paid about 49,50 for my drop in replacement. And you can expect
to pay around 100,- for the FIPK.
Stock the RAM line looks impressive, with some help and care they
can look spectacular. Here are some helpful hints on how to add
modify or maybe even remove from your ram.
Joe (joeandnancy@geocities.com), has the following to say about
rhino liners and drop-in liners;
RHINO PROS: RHINO CONS:
- non-skid - not removable
- last forever - More expensive than drop ins.
- Any color - Can create extra hassle if
truck in accident. (list
members have said that some
body shops will not take
a vehicle with spray-on)
- quiet - If dents occur, you see them.
- no unusable bed space - Need to be concerned
about the installer.
- over or under rail (actually
whatever you want)
- protects bed from minor dents
- can be sprayed around bed
accessories (5th wheel hitch)
DROP-IN PROS: DROP-IN CONS:
- Removable - rubs paint off bed from
shifting motion
- protects bed from minor dents - minimal amount of unused
bed space
- over and under rail - can get hacked
- Removable, you have the option - can rattle
to return your truck to "stock". -
- Easily replaced if truck in accident.
- Less expensive than spray-on.
- Hides dents that do occur.
- Non-skid surface available.
- Lasts forever (life-time warranty on
Duraliner).
- Installs easily.
J Lacey <7th_nhrc@interoz.com> wrote on this;
RHINO LINING
From my place in the Pan handle of FL, Montgomery, AL is the
closest Rhino dealer. Drive up for my 9am appointment. These guys
clean & wash the bed, rough it up with grinder/sander, clean again
with acetone, then apply the goo (after the sanding I sort of liked
the white swirl-look in the bed; too bad we couldn't have left it
at that!) 3 coats bed & sides, come back and add 2 more to bed (5
ttl). Dries within minutes of spraying and I was headed home by
2:30PM. TIP: Watch the guys with the knife - they cut the excess
off. Be sure they do not get into your truck itself with knife.
Jay Eberhard wrote on this;
I have the Mopar running boards. They are covered with black
plastic and come are available for the cab and the bed. I only have
the cab portions on my truck (previous owner did this). I have
thought about switching to the Mopar Nerf Bars to match my grill
guard but thats sometime in the future if at all.
There are many flavors of brush guard available after market, here
are some that list members have installed/like;
Mark Brown (brownmr@co.larimer.co.us), wrote on this;
TJM Bull Bars, imported from Australia by Hella Inc. 800-247-5924
they offer two applications(T1,T17) for late model Dodge Rams.
Reunel Mfg. 800-338-2077 offers extreme duty bumpers for Rams.
(Editors note; expensive, but the most heavy duty bumper on the
market for a RAM today.)
Jay Eberhard wrote on this;
I have the Mopar Grill/Brush guard. They come Chrome, anodized or
black aluminum or black steel. I have the anodized aluminum
Andi Vogt wrote on this;
I went with Warn's full brush guard and winch mount. It looks
great and supports the winch very nicely. The only draw back is
it's low clearance while 4x4ing. I had to remove mine on the trail
as my longer wheelbase added with the overhang (AKA rock magnets)
caused me to need to take too many angular approaches. I found the
uninstall as easy as the install. (Unlike my tow hook install.) I
had to make two vertical cuts in my air dam to install the brush
guard. You can see my guard and one tow hook on my web page
http://www.aros.net/~azure/
Andi Vogt wrote on this;
I use Grizzlies on my 1500 Short box. I selected Grizzlies
because they are a touch shorter than Smittybuilt and mount to the
frame leaving only a 2" gap between them and the lower side panel
of my Ram. They don't cause any rubbing either with my slightly
over sized 32x11.5 Sport Kings. They are not as good a quality as
Smittybuilt, ie. chipping black paint and rust, but they are made
of the same tough high grade steel that Smitty is. I beat the heck
out of them in Moab, and they protected my truck stupendously. A
little sanding and touch up paint and they are as good as new.
They also come with a no-skid strip which I have been thankful for
more than once.
J Lacey <7th_nhrc@interoz.com> wrote on this;
AERO EXTRA FUEL TANK
On the RAM list, April of last year, was posted 2 companies that
offer replacement/auxiliary fuel tanks for RAM. I called both; only
Aero actually did. After I received their brochure I spoke with
Jim (engineer, owner?) who said they had a 40 gal replacement for
1996 ext cab swb 2x4. A second call with further questions & I
spoke with Jacob (installer tech?) who stated no, wasn't suitable,
was for only 4x4, and in a 3rd call Jim this time confirmed
wouldn't fit. Said every time they looked under CC trucks, they'd
changed something and he couldn't keep up.
Same yr, 8 mos later, another call. This time Jim says they NOW
make one to fit my 2x4. Ordered 12/2; cost $389 + $49 for sending
unit + shipping to east coast; arrived 2 days before Christmas.
Attempted to fit up & install during Holidays and found it would fit
close EXCEPT the 2x4 has a cross-over member/carrier for the
extended cab drive shaft and this tank did not take that into
account (I got under a '96 4x4 & checked). A call to Aero and was
told they were shut down for the Holidays; could do zero for 11 days!
Twelve days later & Jim did not act surprised when all was
disclosed. I suggested taking tank to a fabrication shop, the
offending section cut and added lower, tank would then fit and Jim
said they would pick up the shop charges. It was done.
One half day of installation and it's aboard! But even if tank
needed no alteration, it would not have fit as they say. We needed
1"+ to 2" spacers on all corners AND sending unit they provided
could not be used nor was needed. When we called to be sure, they
said it wouldn't work without it but we found the original Dodge
unit WOULD fit and work PERFECT and the gauge shows accurate gallons.
On an incognito call to them this date, 3/12/97, I found they do
not yet differentiate between the 2x4 and 4x4 - one tank fits ALL.
They have yet to admit there is a problem so they're gonna sell you
tank for your RAM and fit be damn. I personally think the tank in
question would have fit a 4x4 pretty good (maybe have to use some
spacers) but at least would go on without adjustments. But I have
yet to see evidence or testimony from Aero that they make a tank,
to replace your OEM one, for the RAM 2x4. And IF they are going to
owe you $$, thats another complete story!
There it is - hauls 40+ gals and when yanking that gas guzzling
5th-wheel, I go a hell of a lot further.
Quite frequently the question comes up about increasing the
brightness/color of the ram headlights. Several people have made
suggestions. As with everything, check with your local authorities
for the legalities of the headlight modifications.
http://www.accessconnect.com/ Seems to carry the bluish tinted
headlights some people have seen. They seem to come in several
different wattages.
The Rams are heavey trucks, and sometimes take some effort to stop.
Several people have been advocating better brake pads, they are
made by Performance Friction and are called Carbon Metallic.
Any self respecting car parts dealer should be able to get them
without much problems. Check when buying, but the part number for
for the 2500 4x4 and diesel& V10 is #04594.
The 2500 and 3500 series are available with an optional 5.9 L
inline 6 cylinder Cummins diesel engine. This is a completely
different beast than any of the gas engines, and as such has an
chapter devoted to it.
Various owners have reported seeing the following; When starting
the engine it seems to take the oil light a few seconds to go off,
and the oil pressure a few seconds to start registering the
operating pressure.
Keith Gardner (keg@bright.net), wrote on this;
Mine has done that since new. It happens because all of the oil
finds its way to the pan (a thin coating remains, but not
much). The oil pump just needs a little time to pump oil out of the
pan and into the motor.
I think the owner's manual states that you should have pressure
within 10 seconds of startup (it may be 5, I'm not real sure).
The Cummins diesel engines takes special "heavy duty" oil, not the
regular motor oil usually used in gasoline engines. The engine oil
must be rated "API CG-4/SH"
david_thom@pop.mindlink.net wrote;
Try Chevron Delo 400 SAE14W-40 or Castrol RX Super SAE 15w-40. Both
of these have labels stating that the product meets or exceeds
Cummins performance specifications.
Joe (Drdonnelly@aol.com), wrote about this;
I use Castrol 15-40RX Super. Both I and my engine machinist like
the stable base stock (compared to Pennzoil, etc). I get about 5
or so more pounds of oil pressure with this oil than with the stuff
the truck came with (Cummins or Dodge oil).
Other guys swear by Shell Rotella T, Chevron Delo 400, etc. I see
Texaco and Pennzoil have oil meeting the specs of 15-40, CG-4, and
SH. S additives are for spark ignition, but some say they are
needed with diesels that have roller lifters or have HEUI injectors
like the PowerStroke. C additives are for compression
ignition--diesels. B engines use solid lifters and conventional
injectors (Bosch). Caterpillar developed HEUI jointly with Navistar.
Dodge recognizes only 4 oil filters for warranty. Any other, and
you are taking your $8000 engine in hand, so to speak. These 4 are
really the same as far as I can tell, the part numbers being Mopar,
Case, Cummins, and Fleetguard. The last is LF3349 and costs me a
couple $ less each than the Mopar #. Case and Cummins designed and
built the B engine as a joint venture. The Rocky Mount NC plant
says something like Consolidated Engines, I am told. Fleetguard is a
Cummins subsidiary. They make a "Microglass" filter that is really
good according to many, but Cummins says it is not really needed
with the duty cycle and change intervals specified by Dodge. I
stick with a 2500-3000 mile change interval, and the LF3349 filter for
"without question" warranty.
Mike Leckey, Jr wrote on this;
I have used Shell Rotella T 15w40 for 7 years. First in my 1990
Cummins, and now in my 1996 CC Cummins.
Editor writes;
I myself use Chevron Delo 400 15W40.
The Cummins diesel on the Ram is incredibly powerful. More
powerful than even the 2500 or 3500 can handle. Here are some
hints to what you can do to get more performance from the Cummins.
Lance Kirk (wolfrider@gorge.net) Suggests;
Without any thought, the biggest "bang to the buck" (IMHO) is to
purchase one of the power increase kits that are advertised in the
Register. The one I've dealt with is from TST Products out of Indiana.
This is a small "family type" business where the owner use to work
for Cummins but now just sells power mods. for the engine.
He sells three kits, all of which cost $349 (this includes postage).
The kits will take your stock 215 HP / 440 LB Torque engine and allow
you to increase to:
#1- 230 HP / 605 LB Torque or
#2- 260 HP / 685 LB Torque or
#3- ??? HP / 770 LB Torque (Sorry don't recall the HP on
this one, but it was like around 290)
(#3 and possibly #2 were NOT recommended for automatics)
Each of these kits comes with a video tape and detailed instructions
showing you how to install the kit. Plus you can call him and ask any
questions about the product or if you need help doing the install.
Sounds great right. So why doesn't everyone do it? Well there are a
few problems. The biggest is that you will without any thought kiss
your warranty good-bye. The second is that the truck (transmission,
driveline) is not designed for this extra increase in torque and if
one is not careful you can and will start overloading and busting
things. (Although the guy who sales this product said they haven't
had many problems with this as long as you don't do stupid things
like popping the clutch.)
I have purchased the 685 LB Torque kit but have not yet installed it
because I'm currently arguing with the dealer over some other warranty
work. So I don't want to modify the engine until all of this other
work is done under warranty and see that it was done right. So it
will be awhile yet. Someone else on the list, Jeff Hammer, if I
got his name right, has installed the 605 Torque kit and apparently
loves it. (I would ask him for further.)
For what it is worth, the guy didn't push or suggest the 770 Torque
option unless you are looking at making some other modifications as
well because it is so powerful.
Starting with the 98 model year Cummins is introducing a new diesel
engine that is replacing the one that they have been putting in the
Ram. This is the new ISB engine, it's main reason for existing
seems to be to meet the new emissions regulations.
This section hopefully provides the reader with some more
background on 4x4 operation. A lot of the info provided in this
section came from Scott Nixon (nixon@sicom.com), Thanks very much
for the additions Scott.!
Ram trucks equipped with 4WD have a full time chain
driven transfer case (NVG231HD in 1500's, NVG241 or NVG241HD
in 2500's and 3500's) that should only be engaged on low
traction surfaces. Usage on pavement can cause damage due
to driveline binding; usage on rain slicked pavement is open
to debate. Some insist it is still a bad idea; personally
I am willing to trade extra tire and driveline wear for the
safety and stability 4WD adds. A good indication is if
the rear wheels slip under moderate throttle input (pedal
to the metal neutral drops DON'T count :), you're probably
safe slipping it into four wheel drive.
All available transfer cases are shift on the fly
for 4Hi and can be engaged by pulling the shift lever
towards you. The drivers manual recommends this only be
done below 55MPH. If done while parked, it may take a
little movement for the system to engage (see below).
Engagement for 4Lo provides an extra 2.72 gear
reduction for use in deep snow, loose sand, and whenever
high torque/low speed operation is desired. For automatics,
come to a near stop (1-3MPG), put the transmission in
neutral, slide the transfer case into 4Lo, and then put
the transmission back in gear. Shifting back into 4Hi
is done by reversing the above procedure. Going all
the way to 2Hi may be easier.
All new Rams use a Central Axle Disconnect (CAD)
system to disconnect the front driveline when in 2WD,
instead of the more traditional hubs. The system consists
of a dog clutch that slides over to connect the two halves
of the passenger side front axle when engaged. Some
wheel movement may be required to get both halves to align.
Owners who purchase a 4WD truck for winter use
only should keep in mind that the vacuum diaphragm that
engages the dog clutch needs to used every month or so
to keep it pliable. This also allows the transfer case
to be lubricated. In other words, if you have 4WD, find a
nice dirt road and use it!!
Here is a list of some of the Lift kits that people on the list
seem to use when they want to rise above the crowds.
TBD
Andi Vogt wrote on this;
IMHO, engaging four wheel drive is like driving a different
vehicle. There are new rules and governing factors that need to be
heeded. In snow and ice, A 4x4 can help you to maintain traction,
but as with any vehicle, excessive speed, inattention, and bad luck
can send you careening out of control. After all, ice is ice and
no vehicle is ever fully control-able, whether front wheel drive,
rear wheel drive or 4 wheel drive.
People get stuck using 4 lo all the time. Factors such as tire tread,
gearing, soil type, and overzealousness influence your Ram's
ability to successfully maneuver many road conditions. If you are
in a mud bog you need to handle your Ram differently than on
slick rock. Even 4 wheelers with decades of experience get in over
their heads.
Four wheel drive is a very useful tool, but a tool none-the-less.
It takes training and experience to learn it's quirks.
John Donovan wrote on this;
The stock differential on the Rams is referred to as an "open"
differential. The diff.. splits the torque equally between the wheels.
So if you imagine a worst-case stuck with one rear wheel on the ground,
and one in the air. The one in the air take very little torque to spin,
and therefore the one on the ground also gets very little torque
and you won't move. Engaging 4 wheel drive turns the front wheels
in the same manner as the rear, if you get one front and one rear
into a situation where they can spin easily, even if the other 2
wheels can get a grip you will still be stuck. See the section on
"traction aiding devices" for more info on what you can do to help
get more traction
For people who spend a lot of time off road open differentials are
unacceptable. However, as with most things in life, gaining more
offload traction involves tradeoffs in cost or on-road
performance. What all traction adding devices do is limit the split of
power between the pair of wheels on an axle. This allows more power
to go to the wheel that grips, but can cause increased tire wear
and handling problems.
John Donovan wrote on this;
The factory LSD is the Dana trac-loc which uses clutch packs to
bias the torque split between the wheels. As factory systems go,
this is one of the better ones out there and for people who only
occasionally go off highway it really is a good choice. If you are
doing a factory order, its only a $250 option, and after the fact
it will cost 2-3 times as much.
John Donovan wrote on this;
From the after market there are several types of LSD/Lockers. The
easiest to install is the lockright, and fairly inexpensive at $350 of
lest for most diffs.. The install can be done by the "shade tree"
mechanic in a few hours and does not require resetting the ring &
pinion gear. The lockright allows a wheel to go faster than the
drive shaft is turning it, but not slower, and provides a 50/50
power split. The problem is on street handling is effected. The
truck will tend to chirp tires in turns, and will also tend to go
straight rather than turn. In low traction rain/snow if you do spin
the wheels the truck will tend to fish tail because both rear wheels
are spinning.
The second option is a gear driven LSD, the most common being an
Auburn. Unlike the factory clutch pack system there is nothing to
wear out, and it generally gives a better torque split between the
slipping and gripping wheel. The cost is similar to the lockrights,
but a professional install is STRONGLY recommended because of the
need to reset the ring & pinion. Installation will run $100-$300
depending on the installers ability to get the ring & pinion set up
correctly without too many retries.
The third kind is a hybrid open/locked diff. called an ARB air locker.
Under normal operation the diff.. operates as an open, but when air
pressure (from a compressor) is applied and the diff. behaves like a
fully locked differential, like the Detroit locker (see
below). They are expensive at $500, plus $200 for a compressor,
plus $100-$300 to install... the general rule of thumb is a
complete ARB system is $1000ish
The fourth kind of locker is the "true" locker, and is also sometimes
referred to as a Detroit or Posi, after Detroit's posi-traction rear
that first showed up in some of the muscle cars of the 60's. When
torque is put on the drive shaft, the diff. locks the right and
left wheels together so they MUST turn at the same speed. This is
very problematic in turns when the wheels are driveling different
diameter circles to go around the curve. Also as you change
throttle position you can cause the diff. to lock and unlock which
results in under/over steer conditions. Also because of the locking
nature of the diff. tire wear is greatly accelerated. The cost is
in the $400 range, plus install.
I've driven trucks with lockrights, track-locs, and Detroit's and there
is a big difference between them. The Detroit is hard to beat off road,
but is hard to live with on road. The lockright is nearly as good
offroad and is more live able on road, but is not as strong...
something to consider if you have a V10 or Cummins up front. The
LSD is almost unnoticeable on road, and does help with
traction. Sure its not as good as the other kinds of lockers, but
its MUCH nicer on highway.
TBD
And there you are with your big 4x4, stuck! So what can you do to
get out equipment wise.?
Andi Vogt wrote on this;
Oh boy!!! I installed my Mopar tow hooks a few months ago and what
a devil it was! My brush guard was already installed and used the
same frame mounts that the hooks needed to use.
If I were to do it again, I would remove my airdam, remove my brush
guard, mount the hooks to the lower holes in the brush guard,
hacksaw off the bolts extra length, and reinstall the brush guard.
Then I would cut out the slots on the airdam for the hooks and
reinstall. Had I done this originally, I would have had less
stress. I didn't do this however, because my brush guard and winch
are just a bit to heavy for me to remove by myself. Next time I
would hire a few muscles to help me.
Bill A wrote on this;
AWDirect (800-243-3194 for catalog) has a winch kit designed
especially for the Dodge Ram using the stock bumper. Includes
Ramsey Pro 9000 winch, cable and a roller fairhead, all mounting
hardware. $1169.00 They also have a wrap-around push bumper (the
type used on wreckers) specifically designed for the Ram. $529.00,
$629.00 for turbo applications.
Towing a 4x4 is somewhat differently than towing a 4x2. Here are
some guidelines and instructions on how to tow a 4x4.
TBD
Here is a list of various http/ftp sites that might be helpful in
finding out more information about all aspects of the Dodge truck line.
http://www.rwilson.com Dodge Ram HQ!! Maintained by
Ron Wilson. Home of the ramtruck
mailing list.!!!
http://www.edmunds.com General car information, good ram
info here to.
http://www.autosite.com Helpful auto/truck related site
Ramtrucks Who is who web page:
http://www.infopage.com/rtml.
This web page is maintained by a member ((joeandnancy@geocities.com))
of the ramtruck mail list. Send adds/changes/deletes to
(joeandnancy@geocities.com)
FAQ for Chrysler:
http://www.allpar.com/faq.html
This FAQ would not be possible without the help of many people,
here is a list of those people who have provided great input to
this FAQ one way or another.
Andi Vogt (azure@mail.aros.net)
Bill A (walleg01@snet.net)
Chris
Chris Siano (Chris_Siano@AutoSite.com)
Darin L Brummett (darinb@juno.com)
Dennis A. Grindrod Sr (grinny@snet.net)
J Lacey (7th_nhrc@interoz.com)
Jay Eberhard (jeberhard@edgenet.net)
Joe (Drdonnelly@aol.com)
Joe (joeandnancy@geocities.com)
John Donovan (jdonovan@us.newbridge.com)
Keith Gardner (keg@bright.net)
Lance Kirk (wolfrider@gorge.net)
Mark Brown (brownmr@co.larimer.co.us)
Michael P. Lebow (hdcc@anet-stl.com)
Mike (mikes@phoenix.net)
Rolando Gonzalez (Lando-G@msn.com)
Scott Nixon (nixon@sicom.com)
Stan Steele (PowerMaster@dodgeram.com)
Steve Belt (Stephen_D_Belt@ccm.ch.intel.com)
Tim Edwards (T_Edwards@eagle2.stark.k12.oh.us)
david_thom@pop.mindlink.net
Bryan Wilemski